Moxa Technologies NPort Server Pro Manuel d'utilisateur Page 14
- Page / 246
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CN2510 User’s Manual Getting Started
2-4
NOTE
Use 8 kg-cm of screw torque and 22-14 AWG electric wire to connect CN2510-8/16-48V’s power
cord to its terminal block.
Grounding CN2510-8/16-48V
V+ V-
SG
ON OFF
Grounding and wire routing helps limit the effects of noise due to electromagnetic
interference (EMI). Run the ground connection from the ground screw to the
grounding surface prior to connecting serial devices to CN2510.
The Shielded Ground (sometimes called Protected Ground) contact is the second contact from the
right of the 5-pin power terminal block connector located on the rear panel of CN2510-8/16-48V.
Connect the SG wire to the Earth ground.
ATTENTION
CN2510-8/16-48V should be mounted to a well-grounded surface, such as a metal panel.
Connecting to the Network
Connect one end of the Ethernet cable to CN2510’s 10/100M Ethernet port and the other end of
the cable to the Ethernet network. There are 2 LED indicators located on the top left and right
corners of the Ethernet connector. If the cable is properly connected, CN2510 will indicate a valid
connection to the Ethernet in the following ways:
81
The top right corner LED indicator maintains a solid green color when the cable is
properly connected to a 100 Mbps Ethernet network.
81
The top left corner LED indicator maintains a solid orange color when the cable is
properly connected to a 10 Mbps Ethernet network.
Connecting to a Serial Device
Use appropriately wired serial data cables to connect serial devices to CN2510’s serial ports.
Connecting to the Console Port
A console is a combination of keyboard and monitor that is used to configure settings and monitor
the status of your system. The console port can be used if a network is unavailable, or you do not
know CN2510’s IP address. To connect to the console port, use a PC running UNIX, or a PC with
terminal emulation software (e.g., HyperTerminal or PComm by Moxa; parameter settings are:
baud rate = 115200 bps, parity check = None, data bits = 8, stop bits = 1, terminal type = VT100).
Use an RJ45-to-DB25 or RJ45-to-DB9 cable to connect the terminal to the console port.
Accessing the Console Utility
The Console Utility is the main application used to set up the server, configure the ports, and run
utilities (ping, diagnosis, monitor, and upgrade). There are two ways to access the Console
Utility—with terminal emulation from a console terminal, or with Telnet from a network terminal.
- Third Edition, June 2006 1
- MOXA Technologies Co., Ltd 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 8
- Product Features 9
- Package Checklist 9
- Front Panel 10
- Rear Panel 10
- Bottom Label 10
- Getting Started 11
- Hardware Installation 12
- Wiring Requirements 13
- Grounding CN2510-8/16-48V 14
- Connecting to the Network 14
- Configuration Checklist 15
- Using Telnet 16
- 7. Click on Close 20
- Server Configuration—Info 23
- Server Configuration—LAN 24
- Server Configuration—Adv 25
- Knowing Your Application 31
- Console LAN 32
- Ethernet 33
- Linux, Unix 33
- Finger Printer 35
- UDP datagram 35
- Terminal Access (Terminal) 37
- Real TTY/Unix Fixed TTY 42
- Configuring ASPP Mode 45
- Installing Ports 56
- Configuration page 63
- Setting 64
- Installing a Server 65
- Setting Up Device Control 88
- Configuring RAW Mode 93
- ASPP Library Introduction 97
- ASPP Examples for Unix 97
- ASPP Examples for Windows 98
- Setting Up Raw UDP 99
- Selecting the Application 101
- Configuring RAW UDP Mode 102
- Configuring the Serial Ports 104
- Restart 105
- Setting Up Reverse Terminal 107
- Configuring RTELNET Mode 110
- Setting Up Terminal 114
- Configuring TERM_ASC Mode 117
- Configuring TERM_BIN Mode 120
- Setting Up Multi-host TTY 125
- Configuring FIXTTY Mode 128
- Setting up Hosts 131
- Configuring tty Redirection 132
- Terminal Access 132
- Using Fixed TTY Driver 133
- Setting Up Dialin/out 134
- Configuring PPPD/PPP Mode 137
- Configuring SLIPD/SLIP Mode 139
- Configuring Dynamic Mode 141
- Optional Welcome Message 148
- Setting Up Printer 151
- Configuring RAW PRN Mode 154
- Configuring LPD PRN Mode 156
- Setting up Unix Hosts 160
- Setting up a LINUX Host 162
- Setting up Windows Hosts 163
- Click on Next to continue 169
- Test Page 171
- Setting Up Multiplex 172
- Code Reader 174
- Equipment 174
- Setting Up Routing 185
- What is RIP? 187
- Configuring RIP 187
- 188
- Internet 189
- 16 port RS-232 Async Server 190
- Administrative Utilities 193
- Monitor 194
- Network 196
- Routing 198
- PPP-Trace 198
- Diagnostic 199
- Upgrade 200
- Console Terminal Upgrade 201
- Remote RCP Upgrade 206
- Console Terminal Export 208
- Remote RCP Export 211
- Console Terminal Import 211
- Default 214
- Press any key to cancel 215
- Appendix A Troubleshooting 216
- Console Terminal Problems 217
- 8 port RS-232 Async Server 218
- Terminal Port Problems 219
- ASPP Port Problems 220
- SLIP/PPP Connection Problems 221
- RADIUS Problems 221
- Appendix B RADIUS Server 222
- What is RADIUS? 223
- Setting up CN2510 223
- Dialin/out—Dynamic Mode 224
- Dialin/out—PPP/PPPD Mode 225
- Setting up UNIX Hosts 226
- Setting up Windows NT Hosts 227
- 6. Specify an IP address 230
- Supported SNMP variables 234
- Pin Assignments 237
- Cable Wiring 237
- Appendix E LCM Display 240
- MOXA Internet Services 243
- Problem Report Form 243
- Product Return Procedure 243
- MOXA Internet Services 244
- Problem Report Form 245
- MOXA CN2510 Series 245
- Product Return Procedure 246
Produits connexes et manuels pour Serveurs Moxa Technologies NPort Server Pro
(69 pages)
(91 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.379 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels