Moxa Technologies NPort 5200 Serie Manuel d'utilisateur Page 14
- Page / 259
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CN2610 User’s Manual Getting Started
2-4
Connecting to a Serial Device
Use appropriately wired serial data cables to connect serial devices to CN2610’s serial ports.
Connecting to the Console Port
A console is a combination of keyboard and monitor that is used to configure settings and monitor
the status of your system. The console port can be used if a network is unavailable, or you do not
know CN2610’s IP address. To connect to the console port, use a PC running UNIX, or a PC with
terminal emulation software (e.g., HyperTerminal or PComm by Moxa; parameter settings are:
baudrate = 115200 bps, parity check = None, data bits = 8, stop bits = 1, terminal type = VT100).
Use an RJ45-to-DB25 or RJ45-to-DB9 cable to connect the terminal to the console port.
Accessing the Console Utility
The Console Utility is the main application used to set up the server, configure the ports, and run
utilities (ping, diagnosis, monitor, and upgrade). There are two ways to access the Console
Utility—with terminal emulation from a console terminal, or with Telnet from a network terminal.
NOTE
If your network is already set up, telnet over the network to CN2610’s IP address to access the
Console Utility. If your network environment is not set up, use Moxa PComm Terminal to
establish a direct serial console connection.
Configuration Checklist
You will need the following information to configure CN2610. Check with your network
administrator if you do not know all of the required information.
Basic CN2610 Information:
Name
Location
LAN1 IP address
LAN1 IP netmask
LAN1 default gateway IP address
LAN2 IP address
LAN2 IP netmask
LAN2 default gateway IP address
Domain server 1 IP address
Domain server 2 IP address
WINS server IP address
Console password
Accessing the Console from a Telnet Terminal
Connect CN2610 to your LAN and then turn on the power. Use the Moxa Windows Utility to find
CN2610’s IP address, and then telnet to the IP address to enter the CN2610 console.
CN2610 Windows Utility
The CN2610 Utility is a convenient Windows utility that can be used to find both the name and IP
address of your CN2610. Once you know the IP address, you can telnet CN2610 over the network
- CN2610 Dual-LAN Async Server 1
- User’s Manual 1
- Copyright Notice 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- Introduction 8
- Product Features 9
- Package Checklist 9
- Front Panel 10
- Rear Panel 10
- Bottom Label 10
- Getting Started 11
- Hardware Installation 12
- Wiring Requirements 13
- Connecting to the Network 13
- Configuration Checklist 14
- Using Telnet 16
- 2. Click Next to Continue 17
- 5. Click Next to continue 18
- 7. Click Close 19
- Server Configuration—Info 22
- Server Configuration—LAN 24
- Server Configuration—Adv 25
- Knowing Your Application 31
- 12345678 32
- Serial ports 32
- 9 10111213141516 32
- Finger Printer 35
- Ethernet 35
- UDP datagram 35
- Terminal Access (Terminal) 39
- Real TTY/Unix Fixed TTY 44
- Configuring ASPP Mode 47
- Installing Ports 58
- Installing a Server 66
- Next to continue 67
- Setting 79
- Setting Up Device Control 90
- Configuring RAW Mode 95
- ASPP Library Introduction 99
- ASPP Examples for Unix 99
- ASPP Examples for Windows 100
- Setting Up Raw UDP 101
- Selecting the Application 103
- Configuring RAW UDP Mode 104
- Configuring the Serial Ports 105
- Restart 107
- Data Acquisition System 108
- Async Server CN2610-8 109
- DRDAS Mode 111
- Setting Up Reverse Terminal 116
- Configuring RTELNET Mode 119
- Setting Up Terminal 123
- Configuring TERM_ASC Mode 126
- Configuring TERM_BIN Mode 128
- Setting Up Multi-host TTY 134
- Configuring FIXTTY Mode 137
- Setting up Hosts 140
- Configuring tty Redirection 141
- Terminal Access 141
- Using Fixed TTY Driver 142
- Setting Up Dialin/out 143
- Configuring PPPD/PPP Mode 146
- Configuring SLIPD/SLIP Mode 148
- Configuring Dynamic Mode 150
- Optional Welcome Message 157
- Setting Up Printer 160
- Configuring RAW PRN Mode 163
- Configuring LPD PRN Mode 165
- Setting up Unix Hosts 168
- Setting up a LINUX Host 170
- Setting up Windows Hosts 171
- Setting Up Multiplex 180
- Code Reader 182
- Equipment 182
- Setting Up Routing 193
- What is RIP? 195
- Configuring RIP 195
- 196
- Static Routing Examples 197
- 16 port RS-232 Async Server 198
- Administrative Utilities 201
- Monitor 202
- Network 204
- Routing 206
- PPP-Trace 206
- Diagnostic 207
- Upgrade 208
- Console Terminal Upgrade 209
- Remote RCP Upgrade 214
- Console Terminal Export 216
- Remote RCP Export 219
- Console Terminal Import 219
- Default 222
- Press any key to cancel 223
- Appendix A Troubleshooting 224
- Console Terminal Problems 225
- Terminal Port Problems 227
- Saving CN2610’s Parameters 228
- ASPP Port Problems 228
- SLIP/PPP Connection Problems 228
- RADIUS Problems 229
- Appendix B RADIUS Server 230
- What is RADIUS? 231
- Setting up CN2610 231
- Dialin/out—Dynamic Mode 232
- Dialin/out—PPP/PPPD Mode 233
- Setting up UNIX Hosts 234
- RADIUS Server Configuration 235
- Add/Modify permission group 236
- Basic Permission Maintenance 237
- User Settings 238
- RADIUS proxy 239
- Setting up Windows NT Hosts 240
- 6. Specify an IP address 243
- Supported SNMP variables 247
- Pin Assignments 250
- Cable Wiring 250
- Appendix E LCM Display 253
- Problem Report Form 256
- Product Return Procedure 256
- MOXA Internet Services 256
- MOXA Internet Services 257
- Problem Report Form 258
- MOXA CN2610 Series 258
- Product Return Procedure 259
Produits connexes et manuels pour Serveurs Moxa Technologies NPort 5200 Serie
(66 pages)
(91 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels